본문 바로가기

리눅스

우분투에서 VSFTPD를 설치하고 설정하는 방법

728x90

우분투에서 VSFTPD를 설치하고 설정하는 방법

VSFTPD (Very Secure File Transfer Protocol Daemon)는 Linux 시스템에서 FTP 서버를 구축하고 관리하기 위한 효과적인 도구 중 하나입니다.

테스트 환경

운영체제 버전 정보 확인

$ lsb_release -d
Description:    Ubuntu 22.04.3 LTS

1. VSFTPD 설치

vsftpd 패키지를 설치합니다. 터미널에서 다음 명령을 사용합니다.

sudo apt-get update
sudo apt-get install vsftpd

vsftpd 버전 정보 확

$ vsftpd -v
vsftpd: version 3.0.5

2. VSFTPD 설정 파일 수정

VSFTPD의 설정은 /etc/vsftpd.conf 파일에서 관리됩니다. 이 파일을 텍스트 에디터로 열고 필요한 설정을 변경합니다. 기본적으로 대부분의 설정은 안전한 기본값으로 설정되어 있습니다.

  • anonymous_enable=NO: 익명 FTP 액세스 비활성화.
  • local_enable=YES: 로컬 사용자에 대한 로그인 허용.
  • write_enable=YES: 로컬 사용자가 파일을 업로드할 수 있도록 허용.
  • chroot_local_user=YES: 로컬 사용자를 홈 디렉토리로 제한.
  • local_umask=022: 로컬 사용자에 대한 기본 UMASK 설정.

설정을 변경한 후 파일을 저장하십시오.

더보기

---

cat /etc/vsftpd.conf
# Example config file /etc/vsftpd.conf
#
# The default compiled in settings are fairly paranoid. This sample file
# loosens things up a bit, to make the ftp daemon more usable.
# Please see vsftpd.conf.5 for all compiled in defaults.
#
# READ THIS: This example file is NOT an exhaustive list of vsftpd options.
# Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's
# capabilities.
#
#
# Run standalone?  vsftpd can run either from an inetd or as a standalone
# daemon started from an initscript.
listen=NO
#
# This directive enables listening on IPv6 sockets. By default, listening
# on the IPv6 "any" address (::) will accept connections from both IPv6
# and IPv4 clients. It is not necessary to listen on *both* IPv4 and IPv6
# sockets. If you want that (perhaps because you want to listen on specific
# addresses) then you must run two copies of vsftpd with two configuration
# files.
listen_ipv6=YES
#
# Allow anonymous FTP? (Disabled by default).
anonymous_enable=NO
#
# Uncomment this to allow local users to log in.
local_enable=YES
#
# Uncomment this to enable any form of FTP write command.
#write_enable=YES
#
# Default umask for local users is 077. You may wish to change this to 022,
# if your users expect that (022 is used by most other ftpd's)
#local_umask=022
#
# Uncomment this to allow the anonymous FTP user to upload files. This only
# has an effect if the above global write enable is activated. Also, you will
# obviously need to create a directory writable by the FTP user.
#anon_upload_enable=YES
#
# Uncomment this if you want the anonymous FTP user to be able to create
# new directories.
#anon_mkdir_write_enable=YES
#
# Activate directory messages - messages given to remote users when they
# go into a certain directory.
dirmessage_enable=YES
#
# If enabled, vsftpd will display directory listings with the time
# in  your  local  time  zone.  The default is to display GMT. The
# times returned by the MDTM FTP command are also affected by this
# option.
use_localtime=YES
#
# Activate logging of uploads/downloads.
xferlog_enable=YES
#
# Make sure PORT transfer connections originate from port 20 (ftp-data).
connect_from_port_20=YES
#
# If you want, you can arrange for uploaded anonymous files to be owned by
# a different user. Note! Using "root" for uploaded files is not
# recommended!
#chown_uploads=YES
#chown_username=whoever
#
# You may override where the log file goes if you like. The default is shown
# below.
#xferlog_file=/var/log/vsftpd.log
#
# If you want, you can have your log file in standard ftpd xferlog format.
# Note that the default log file location is /var/log/xferlog in this case.
#xferlog_std_format=YES
#
# You may change the default value for timing out an idle session.
#idle_session_timeout=600
#
# You may change the default value for timing out a data connection.
#data_connection_timeout=120
#
# It is recommended that you define on your system a unique user which the
# ftp server can use as a totally isolated and unprivileged user.
#nopriv_user=ftpsecure
#
# Enable this and the server will recognise asynchronous ABOR requests. Not
# recommended for security (the code is non-trivial). Not enabling it,
# however, may confuse older FTP clients.
#async_abor_enable=YES
#
# By default the server will pretend to allow ASCII mode but in fact ignore
# the request. Turn on the below options to have the server actually do ASCII
# mangling on files when in ASCII mode.
# Beware that on some FTP servers, ASCII support allows a denial of service
# attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd
# predicted this attack and has always been safe, reporting the size of the
# raw file.
# ASCII mangling is a horrible feature of the protocol.
#ascii_upload_enable=YES
#ascii_download_enable=YES
#
# You may fully customise the login banner string:
#ftpd_banner=Welcome to blah FTP service.
#
# You may specify a file of disallowed anonymous e-mail addresses. Apparently
# useful for combatting certain DoS attacks.
#deny_email_enable=YES
# (default follows)
#banned_email_file=/etc/vsftpd.banned_emails
#
# You may restrict local users to their home directories.  See the FAQ for
# the possible risks in this before using chroot_local_user or
# chroot_list_enable below.
#chroot_local_user=YES
#
# You may specify an explicit list of local users to chroot() to their home
# directory. If chroot_local_user is YES, then this list becomes a list of
# users to NOT chroot().
# (Warning! chroot'ing can be very dangerous. If using chroot, make sure that
# the user does not have write access to the top level directory within the
# chroot)
#chroot_local_user=YES
#chroot_list_enable=YES
# (default follows)
#chroot_list_file=/etc/vsftpd.chroot_list
#
# You may activate the "-R" option to the builtin ls. This is disabled by
# default to avoid remote users being able to cause excessive I/O on large
# sites. However, some broken FTP clients such as "ncftp" and "mirror" assume
# the presence of the "-R" option, so there is a strong case for enabling it.
#ls_recurse_enable=YES
#
# Customization
#
# Some of vsftpd's settings don't fit the filesystem layout by
# default.
#
# This option should be the name of a directory which is empty.  Also, the
# directory should not be writable by the ftp user. This directory is used
# as a secure chroot() jail at times vsftpd does not require filesystem
# access.
secure_chroot_dir=/var/run/vsftpd/empty
#
# This string is the name of the PAM service vsftpd will use.
pam_service_name=vsftpd
#
# This option specifies the location of the RSA certificate to use for SSL
# encrypted connections.
rsa_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem
rsa_private_key_file=/etc/ssl/private/ssl-cert-snakeoil.key
ssl_enable=NO

#
# Uncomment this to indicate that vsftpd use a utf8 filesystem.
#utf8_filesystem=YES

---

vim /etc/vsftpd.conf
listen=NO

listen_ipv6=YES

anonymous_enable=NO

local_enable=YES

dirmessage_enable=YES

use_localtime=YES

xferlog_enable=YES

connect_from_port_20=YES

secure_chroot_dir=/var/run/vsftpd/empty

pam_service_name=vsftpd

rsa_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem
rsa_private_key_file=/etc/ssl/private/ssl-cert-snakeoil.key
ssl_enable=NO

write_enable=YES

#user_sub_token=$USER
#local_root=/home/$USER

 

  • write_enable=YES : 사용자에게 파일을 업로드할 권한을 부여합니다.
  • user_sub_token=$USER : 사용자의 홈 디렉토리를 지정할 때 $USER 토큰을 사용합니다.
  • local_root=/home/$USER/ftp : 사용자의 홈 디렉토리를 /home/$USER/ftp로 지정합니다. 사용자 이름을 통해 각 사용자의 홈 디렉토리로 전송할 수 있게 됩니다.

3. Firewall 설정

FTP 서버를 사용하려면 방화벽 규칙을 업데이트하여 FTP 포트(기본적으로 21번 포트)를 허용해야 합니다.

sudo ufw allow 21/tcp

필요한 경우 SSL을 사용할 때 990/tcp (FTPS) 및 passive mode를 사용할 때 범위로 포트를 추가해야 할 수 있습니다.

4. 서비스 시작 및 활성화

VSFTPD 서비스를 시작하고 부팅 시 자동 시작하도록 활성화합니다.

sudo systemctl start vsftpd
sudo systemctl enable vsftpd

5. 사용자 계정 및 홈 디렉토리 설정

사용자 계정을 생성하고 FTP 서버에 액세스할 수 있도록 사용자 홈 디렉토리를 설정합니다.

  • 사용자 추가
sudo adduser myuser
  • 사용자 홈 디렉토리 변경
sudo usermod -m -d /path/to/directory myuser

사용자에게 로그인을 허용하려면 해당 사용자에게 FTP 액세스를 허용하도록 vsftpd.conf 파일을 구성해야 합니다.

6. VSFTPD 재시작

설정을 변경한 후 VSFTPD 서비스를 재시작하여 변경 사항을 적용합니다.

sudo systemctl restart vsftpd

 

VSFTPD가 설치되었고 설정되었습니다.

728x90

1. FTP 클라이언트 설치

sudo apt update
sudo apt install ftp

2. FTP 클라이언트를 실행하고 서버에 연결

  • ftp 명령어 옵션
$ ftp -?
usage: ftp [-46AadefginpRtVv] [-N NETRC] [-o OUTPUT] [-P PORT] [-q QUITTIME]
           [-r RETRY] [-s SRCADDR] [-T DIR,MAX[,INC]] [-x XFERSIZE]
           [[USER@]HOST [PORT]]
           [[USER@]HOST:[PATH][/]]
           [file:///PATH]
           [ftp://[USER[:PASSWORD]@]HOST[:PORT]/PATH[/][;type=TYPE]]
           [http://[USER[:PASSWORD]@]HOST[:PORT]/PATH]
           [https://[USER[:PASSWORD]@]HOST[:PORT]/PATH]
           ...
       ftp -u URL FILE ...
       ftp -?

3. 파일 업로드

  • FTP 명령을 사용한 업로드
ftp [email protected]
  • 로컬 디렉토리에서 파일 목록 표시
!ls
  • 로컬 파일을 원격 서버로 전송
put datafile.txt
$ ftp [email protected]
Connected to 192.168.56.211.
220 (vsFTPd 3.0.5)
331 Please specify the password.
Password:
230 Login successful.
Remote system type is UNIX.
Using binary mode to transfer files.
ftp> !ls
datafile.txt
ftp> put datafile.txt
local: datafile.txt remote: datafile.txt
229 Entering Extended Passive Mode (|||24779|)
150 Ok to send data.
100% |********************************************************************|     9       32.55 KiB/s    00:00 ETA
226 Transfer complete.
9 bytes sent in 00:00 (2.70 KiB/s)
  • 원격 서버 디렉토리에서 파일 목록 표시
ls
  • 원격 서버 파일을 로컬로 다운로드
get remote_file
  • 로컬 디렉토리로 이동
lcd local_directory

4. 업로드 완료 확인

파일 업로드가 완료되면 FTP 클라이언트에서 성공 메시지가 표시됩니다. 또한 원격 서버의 파일 시스템에서 업로드한 파일을 확인할 수 있습니다.

 

파일 업로드를 완료하면 VSFTP 서버에 파일이 저장되고 필요한 경우 다운로드하거나 공유할 수 있습니다.

 

728x90